Usually in order to characterize plotted data more completely, it helps to add a target line to your chart. There are a number of ways to do this in an Excel chart. If your chart is a column chart, you can add another column series, you can add a line series that spans the middle of the first column to the middle of the last, you can add an XY series that spans the entire chart, or you can add an XY point with an error bar that spans the chart.

We are plotting how five employees of our widget factory perform against their target of 22 widgets. Here is the data; ignore the extra data beyond column C for now.

A plain chart of the employees’ performance is shown here. This column chart was created using the data in A1:B6.

To add a column series or a line series, the first step is to expand the data to include A1:C6. That is as simple as selecting the chart’s plot area or chart area, then dragging on the corner of the highlighted source data range until it includes the entire range needed. You could also copy the data and paste it into the chart, drag the data onto the chart (if you’re not using Excel 2007), or use the Source Data dialog to add a series with the appropriate data.

- - -

The result is a clustered column chart with two series.

Putting the target right next to the values makes the chart a bit counterintuitive for the reader, so we’ll take a different tack. Format the target series so it is plotted on the secondary axis.

Now format it to have a border and no fill (usually I format column series to have a fill but no border). Then you can adjust the gap width if you like. I usually use a gap width of 100 (the default is 150), which means the gap between clusters is equal to 100% of the width of a single column. Below, I’ve made the gap width of the secondary series about 50.

You could also use the same gap width for both, so it looks like the values are filling up the targets. I’ve used formatting that has a bit better contrast.

While the dual-column approach works well enough, it’s usually not as nice as the other techniques. To use a line series, start with the clustered column chart from above.

Right click on the target series, choose the Chart Type command, and choose a line type. You should choose a type here with no markers, but I’ve left the markers for illustration purposes.

The markers are gone, and I’ve added a data label to the last point showing the target value.

The line and column combination chart is not bad, but the line doesn’t extend to the edges of the chart. The solution, described on my web site but also demonstrated here, is to add an XY series to produce the line. Using what we learned in Integer Values on Line Chart Category Axis, we know that the starting and ending X values for the XY series are 0.5 and 5.5, since the categories have effective X values of 1 through 5.

Start with the column chart with a single series, the values. Copy the data in E1:F3, select the chart, and use Paste Special to add the data to the chart as a new series, with series data in columns, series names in the first row, and categories in the first column.

Right click on the target series, choose the Chart Type command, and choose an XY type. You should choose a type here with no markers, but I’ve left the markers for illustration purposes. Excel moves an XY series to the secondary axis when it is added to a column or line chart, so this chart has primary and secondary axes.

Format the target series so it is plotted on the primary axis. Now the target line spans the entire chart.

Remove the markers. In the chart below I’ve added a data label to the second point, to show the target value. You could add this or another label to either or both points.

An alternative to a two-point XY chart for a target line is a one-point line with an error bar, as described on my web site. Start with the initial column chart with just the values. Copy the data in H1:I2, select the chart, and use Paste Special to add the data to the chart as a new series, with series data in columns, series names in the first row, and categories in the first column. (H2 contains the X value 5.5, so the point lies along the right edge of the chart; use 0.5 to position the point on the left edge of the chart.)

Right click on the target series, choose the Chart Type command, and choose an XY type. You should choose a type here with no markers, but I’ve left the markers for illustration purposes. Excel moves an XY series to the secondary axis when it is added to a column or line chart, so this chart has primary and secondary axes.

While formatting, add a negative horizontal error bar, with a length of 5, to the XY data point.

Format the color of the error bar to match the desired target line color, and choose the error bar style without end caps.

Format the target series so it is plotted on the primary axis. Now the target line (error bar) spans the entire chart.

Remove the data point marker, and if desired add a label.

The error bar approach is convenient if you want a series of lines across the chart. The data for the target series would have multiple rows like this:

This data produces three points along the right edge of the chart, each with an error bar and data label.

Possibly Related Posts:

• Adding an Arbitrary Target
• Integer Values on Line Chart Category Axis
• Clustered-Stacked-Column Combo Chart With Lines
• Clustered-Stacked Column Charts with Vertical Separators
• Add Percentages on the Secondary Axis
• US Employment Slump Chart - How To
• Clustered-Stacked Bar Charts
• Individually Formatted Category Axis Labels